Fascias.com - Quality Building Plastics

NEW NEW NEW NEW NEW NEW NEW

• Many uses as a Car Port, Patio Canopy, Door Canopy, Covered Play Area, Protected Walkway.
• Advanced cantilever design is self-supporting. No excavations foundations or supporting pillars are needed.
• Range of gloss colours that never need painting.
• Translucent roof panels let daylight through
• Can be erected by two fitters in eight hours easily.
• Modular construction allows future expansion.

Cantilever Carport-Canopy is designed on a modular basis which means that you can increase the area of the cover at any time and there are no support pillars needed.
Your canopy will keep its good looks for years and years without continual upkeep. All you need to maintain the elegant looks is an occasional wipe clean.
The tough translucent roof panels allow natural daylight through, so if your canopy is above your kitchen window, patio or living room, adequate daylight still enters your home. Adds value to your property.
Cantilever Carport-Canopy requires no ground preparation and in most cases planning permission is not necessary (Call your local planning authority to check.) ALL MATERIALS ARE GUARANTEED FOR FIVE YEARS.

Cantilever Carport-Canopy are sold in a standard 2.440mm width but smaller widths can be manufactured at no extra cost.

Fascias.com offer a range of Carports with a choice of sizes and polycarbonate colours delivered to your door in the UK. Made from powder coated aluminum and polycarbonate. The kits come complete including posts and wall plates. Ideal for protecting your car or offering shade and privacy to your patio area.

You purchase the carport range direct from our website, and we will deliver direct to your door.

Carports

Garden Canopy

Patio Canopies

Key Points

Polycarbonate sheets are used which are virtually unbreakable.
Panels are made with shatter proof polycarbonate in bronze clear or opal 10mm twin wall sheets.
Strong Panels are pre glazed and require no intermediate supports multiple panels can be installed to any width required
Long Term Maintenance Free The polycarbonate sheets carry a ten year guarantee and the frame work is made of rust proof aluminum.
Ready To Fit Standard panels 610mm wide are pre assembled and readily available with all the necessary fittings and accessories.
Attractive and Inexpensive From a plain patio to an elegant covered all weather seating area adding value and distinction to
your property and making better use of your garden.

INSTALLATION GUIDE

SELF SUPPORT ROOF FIXING GUIDE

Before you start approximately 4 inches above your intended wall plate height cut a grove into the wall

1. First decide on the correct height for the aluminum wall plate (5 to 10 degrees) then ensuring it is level fix it to the wall at approximately every 600mm note pvc under cladding should be on wall plate before fixing

2. There is a grove along the length of the wall plate designed to take captive bolts slide these bolts into place allowing two per bar.

3. Drill a pair of holes into the end of each bar30mm from the top of the bar then pass the bolts through the holes you have drilled secure into position with fixing nut. (bar spacing = sheet size + 8mm

4.Offer aluminum end closure up to wall on top of glazing bars and mark glazing bar centers. Then cut a notch into the bottom of the profile approximately 5mm wide up to the up stand. This profile should then locate onto the end of glazing bars. Check it

5.The lower end of the bar should be drilled into a the lower wall plate( not supplied) you can either use timber 4x4 which can be clad later or if using upvc windows a purpose designed wall plate.

6.Cut bars to length (remember to allow 60mm into the guttering) then cut your sheets to length (remove swarf from sheets with a vacuum then seal sheets with anti dust tape) solid tape goes on the top edge of the poly vented on the bottom edge.

7.Fit polycarbonate sheets in place and locate into aluminium closure silicone to seal sheets

USE NEUTRAL CURE SILICONE

8.Fit upvc capping onto bar and push up in to aluminium closure profile silicone where pvc capping meets aluminum flashing

9.Slide the variable angle flashing support trim along the aluminum closure then dress lead into the precut grove then down the wall and onto the lead flashing

support trim dress the lead and trim as required.

10. Fit sides to edge bars clip into place then use double sided tapes to fix. Now place sheet upvc closures to bottom edge of polycarbonate sheets fit bar end caps and install your gutter system as norm

TOP TIP

TIPS Always seal sheets with anti dust tapes to prevent dust

insects and reduce condesation .Always leave 4mm expansion gaps each side of the sheet.Never use solvent cleaner to clean your sheets just use a very mild soapy warm water.

Read the cling film on the sheet to ensure the ultra violet protected side faces the sun.

Self supporting ali bars can be used with 16 mm or 25 mm sheets