fascias.com

Description: A170 drip fascia trim (3 metre length)

The A170 drip facia trim matchs the B230 raised edge trim.
These small size trims are normally used on small roof areas such as porches.

Weight 1.3 kg
Girth   170 mm
Depth  65 mm

Description: A200 drip fascia trim (3 metre length)

Weight 1.3 kg
Girth   200 mm
Depth  90 mm

Description: A250 drip fascia trim (3 metre length)

The A250 drip facia trim matchs the B300 raised edge trim.
These large size trims are normally used on commercial roof areas or in general where the top of the existing fascia is to low for a smaller trim

Weight 1.3 kg
Girth   250 mm
Depth 140 mm

Description: B230 raised edge trim

The A170 drip facia trim matchs the B230 raised edge trim.
These small size trims are normally used on small roof areas such as porches.
These trims come in three sizes and are fitted to the roof edge allowing drainage into the gutter.

Weight 1.3 kg
Girth   230 mm
Depth  105 mm

Description: B260 raised edge trim

The A200 drip facia trim matchs the B260 raised edge trim.
These medium size trims are normally used on domestic and small commercial roof areas and are the most commonly used.
These trims come in three sizes and are fitted to the roof edge allowing drainage into the gutter.

Weight 1.3 kg
Girth   260 mm
Depth 125 mm

Description: B300 raised edge trim

The A250 drip facia trim matchs the B300 raised edge trim.
These large size trims are normally used on commercial roof areas or in general where the top of the existing fascia is too low for a smaller trim.
These trims come in three sizes and are fitted to the roof edge allowing drainage into the gutter.

Weight 1.3 kg
Girth   300 mm
Depth 180 mm

Description: Wall fillet trim (3 metre length)

For use where the flat roof butts against a wall creating an up stand

Weight 1.3 kg Girth 260 mm
Fillet    135 & 70 mm
Upstand height 120 mm

Description: C100L simulated lead flashing trim, long leg

Replaces traditional lead flashing for fixing into brickwork where a flat roof butts against a wall. This product is often used in situations where lead may be stolen after installation.

Weight 1.3 kg
Vertical cover   100 mm
Wall penetration 50 mm

Description: C150L simulated lead flashing trim, long leg

Replaces traditional lead flashing for fixing into brickwork where a flat roof butts against a wall. This product is often used in situations where lead may be stolen after installation.

Weight 1.3 kg
Vertical cover   150 mm
Wall penetration 50 mm

Description: AT195INT internal angle trim (3 metre)

This general purpose angle is useful in situations where the usual trims may not fit.

Internal angle trim has the high adhesion surface on inner face for forming upstands, gutter floors etc.

External angle trim has the high adhesion surface on outer face for step details, cover flashings etc.

Weight: 1.3 kg
Girth: 195 mm
Flange widths: 105 mm & 85 mm

Description: E280 expansion joint trim (3 metre)

Expansion joint trim (3 metre length)

Used both to create expansion joints on large roofs and to create rolls on any ridge details. We recommend using expansion joints on installations exceeding 10 metres in any direction.

Weight    1.3 kg
Girth        280 mm
Flanges    90 mm
Height       50 mm

Description: E35/40 simulated lead rolled joint (3 metre)
Simulated lead rolled joint
Used to simulate the appearance of raised rolled lead joints. Also provides expansion.

Weight   1.3 kg
Girth  130 mm Flanges   20 mm
Height 40 mm Roll width 35 mm

Description: AT195EXT external angle trim (3 metre)

This general purpose angle is useful in situations where the usual trims may not fit.

Internal angle trim has the high adhesion surface on inner face for forming upstands, gutter floors etc.

External angle trim has the high adhesion surface on outer face for step details, cover flashings etc.

Weight: 1.3 kg
Girth: 195 mm
Flange widths: 105 mm & 85 mm

Description: C1 universal external corner
These fittings are hot press moulded in GRP, giving a neat finish to both right & left hand external corners. For use with any combination of A200 and B260 trims.

Weight  200 grams

Hot press moulded  pre formed GRP

Description: C4 universal internal corner

These fittings are hot press moulded in GRP, giving a neat finish to both right & left hand external corners. For use with any combination of A200 and B260 trims.

Weight  200 grams

Hot press moulded  pre formed GRP

C3INT internal fillet corner

Fillet corner joints

These fittings are hot press moulded in GRP, giving a neat finish to both right & left hand external corners. For use with D260 trim. Avoids mitring in situ.

Weight  200 grams
Hot press moulded  pre formed GRP

C3EXT external fillet corner

Fillet corner joints

These fittings are hot press moulded in GRP, giving a neat finish to both right & left hand external corners. For use with D260 trim. Avoids mitring in situ.

Weight  200 grams
Hot press moulded  pre formed GRP

Click Here to view the Safety Data Sheets for Fibreglass Roofing Products